HEALTH & WELFARE: $5.55 per hour, up to 40 hours per week, or $222.00 per week or $962.00 per month | VACATION: 1 week of paid vacation after 1 year of service with a contractor or successor; 2 weeks after 2 years; 3 weeks after 10 years; and 4 weeks after 20 years. Length of service includes the whole span of continuous service with the present contractor or successor, wherever employed, and with the predecessor contractors in the performance of similar work at the same Federal facility. (Reg. 29 CFR 4.173) | HOLIDAYS: A minimum of eleven paid holidays per year: New Year's Day, Martin Luther King Jr.'s Birthday, Washington's Birthday, Memorial Day, Juneteenth National Independence Day, Independence Day, Labor Day, Columbus Day, Veterans' Day, Thanksgiving Day, and Christmas Day. (A contractor may substitute for any of the named holidays another day off with pay in accordance with a plan communicated to the employees involved.) (See 29 CFR 4.174) NOTE: The fringe benefits listed in this determination are based on a standard 8- hour workday an 40-hour work week. Cash equivalent fringe benefits may be paid in accordance with the principles discussed in Subpart B of Regulations, 29 CFR Part 4. HEALTH & WELFARE & PENSON PAYMENTS: These payments are due on all hours """"paid for"""" up to a maximum of 40 hours per week. Such benefits do not stop, but continue to accrue and are paid to employees while on sick leave, holiday, vacation, etc. For example: a. An employee who works four days, 40 hours per week, is entitled to 40 hours of health and welfare and pension payments. If an employee works three days, 12 hours per day, then such employee is entitled to 36 hours of health and welfare and pension benefits. b. An employee who works 32 hours and also receives eight hours of holiday pay is entitled to the maximum of 40 hours of health and welfare and pension payments in that work week. If the employee works more than 32 hours and also receives eight hours of holiday pay, the employee is still only entitled to the maximum of 40 hours health and welfare and pension payment. c. If an employee is off work for two weeks on vacation and receives 80 hours of vacation pay, the employee must also receive 80 hours of health and welfare and pension benefits during the vacation period. However, if an employee is entitled to two weeks paid vacation but does not take a vacation and works the full 52 weeks in they year (i.e., 52 weeks for work plus two weeks of vacation pay) the employee is due health and welfare and pension payments for only 52 weeks during the year. VACATION AND HOLIDAY PAYMENTS: Regardless of the number of hours in an employee's scheduled workday or work week, holiday pay for one day is not required to exceed the equivalent of eight hours pay, and vacation pay for one week is not required to exceed the equivalent of 40 hours pay. ** UNIFORM ALLOWANCE ** If employees are required to wear uniforms in the performance of this contract (either by the terms of the Government contract, by the employer, by the state or local law, etc.), the cost of furnishing such uniforms and maintaining (by laundering or dry cleaning) such uniforms is an expense that may not be borne by an employee where such cost reduces the hourly rate below that required by the wage determination. The Department of Labor will accept payment in accordance with the following standards as compliance: The contractor or subcontractor is required to furnish all employees with an adequate number of uniforms without cost or to reimburse employees for the actual cost of the uniforms. In addition, where uniform cleaning and maintenance is made the responsibility of the employee, all contractors and subcontractors subject to this wage determination shall (in the absence of a bona fide collective bargaining agreement providing for a different amount, or the furnishing of contrary affirmative proof as to the actual cost), reimburse all employees for such cleaning and maintenance at a rate of $3.35 per week (or $.67 cents per day). However, in those instances where the uniforms furnished are made of """"wash and wear"""" materials, may be routinely washed and dried with other personal garments, and do not require any special treatment such as dry cleaning, daily washing, or commercial laundering in order to meet the cleanliness or appearance standards set by the terms of the Government contract, by the contractor, by law, or by the nature of the work, there is no requirement that employees be reimbursed for uniform maintenance costs. ** SERVICE CONTRACT ACT DIRECTORY OF OCCUPATIONS ** The duties of employees under job titles listed are those described in the """"Service Contract Act Directory of Occupations"""", Fifth Edition (Revision 1), dated September 2015, unless otherwise indicated. ** OCCUPATIONS NOT INCLUDED IN THE SCA DIRECTORY OF OCCUPATIONS ** Driver/Caser Drives motor powered vehicle to make box delivery of mail, often along a designated route, picks up and transports collection mail left in boxes or receptacles. May also sort mail for delivery to boxes along the route, incidentally transports collection mail left in boxes or receptacles. May also sort mail for delivery to boxes along the route, incidentally transport mail to or between postal or other designated facilities, make minor vehicle repairs and keep vehicle in good working order. Light Vehicle Driver Drives motor powered vehicle with a nominal cargo capacity of 600 cubic feet or less and with a GVW rating under 10,001 pounds GVWR or less to transport mail, often along a designated route to or between designated postal or other facilities. May also pickup and transport collection mail, load and unload vehicle with or without helpers, make minor vehicle repairs, and keep vehicle in good working order. Tractor Trailer Driver Drives motor powered tractor-trailer combination to transport mail, often along a designated route to or between designated postal or other facilities. May also load and unload vehicle with or without helpers, make minor vehicle repairs, and keep vehicle in good working order. Truck Driver Drives motor powered truck, other than tractor-trailer, with a nominal* cargo capacity of 333 cubic feet or more or with a gross volume weight of 10,000 pounds or more to transport mail, often along a designated route to or between designated postal or other facilities. May also pickup and transport mail, load and unload truck with or without helpers, make minor vehicle repairs, and keep vehicle in good working order. *(Nominal cargo capacity means an actual cargo capacity of plus or minus 5% of the stated capacity, rounded to the nearest whole cubic foot.)
Weatherization Assistance Program - Multi-Trade Residential Improvements
Federal opportunity from Strategic Procurement Department (SPD) • Miami-Dade County. Place of performance: FL. Response deadline: May 12, 2026.
Support routes that fit this solicitation
Market snapshot
Baseline awarded-market signal across all contracting (sample of 400 recent awards; refreshed periodically).
Related hubs & trends
Navigate the lattice: hubs for browsing, trends for pricing signals.
Applicable Wage Determinations
SAM WDOL references matched to this opportunity's location and scope language.
View more for this contract3 more WD matches for this notice.↓
Point of Contact
Agency & Office
Description
Scope of Work 1 Pages 1 - 8 Folio # 30-7909-028-0930 Work Site Address: 30505 SW 152 Court INSTALL SMOKE DETECTORS: Furnish and install battery-operated smoke alarms that are listed and labeled in accordance with UL 217 and have sealed, non-replaceable, 10-year batteries along with a tamper proof cover is required. Install battery-operated smoke alarms in the locations required by the Authority Having Jurisdiction (AHJ) Install battery-operated smoke alarms in accordance with the manufacturer's instructions and Miami Dade residential code. Materials_____________ Locations: In All Locations needed Labor________________ Quantity:4 INSTALL CO DETECTOR: Furnish and install CO alarms (Carbon Monoxide Detector) that are listed and labeled in accordance with UL 2034, or approved by the authority having jurisdiction, and have a minimum of: 10-year manufacturer's warranty Contain internal non-replaceable batteries along with tamper proof covering near gas appliances. Install CO alarms in the locations required by the Authority Having Jurisdiction (AHJ) Install CO alarms in accordance with the manufacturer's instructions The installed location must not interfere with or obstruct any cabinet or drawer functions. Materials_______________ Location: Hallway Sleeping Room Area Labor__________________ Quantity: 1 PROVIDE A/C AIR FILTER: Remove and replace disposable pleated AC filter with filtration must meet a minimum efficiency of MERV 8 or better and leave the extra with homeowner. Filter opening must allow filter to be fully removed and inserted without bending or damaging the filter Materials______________ Quantity: 2 PROVIDE LED LIGHT BULBS: Furnish new Energy Star certified LED bulbs, and replace incandescent light lighting level quality required for the intended application (e.g., task lighting, hazards lighting, nightlights) is the highest level of efficiency within a technology (e.g., LED bulbs) are ENERGY STAR® qualified, equivalent or better, and UL approved Install lighting in accordance with manufacturer specifications and applicable code (i.e., NFPA 70, NFPA 101, NECA/IESNA 500) If applicable, clean the lens and reflector before installing new bulb Safe and proper installation. Permanently remove old products from job sites and recycle or dispose of in accordance with local and federal law (e.g., EPA Section 608 of Clean Air Act of 1990) Materials _________________ Quantity 12 Labor ____________________ Location: INSTALL NEW MICROWAVE WITH DUCT TO OUTSIDE EXHAUST FAN: All kitchens must have a minimum of 160 CFM on-demand fan (1 sone maximum for continuous use). All exhaust must be reduced and must terminate to the outside or exterior of the residence. Labor & Materials maximum allowable cost $600.00. Materials _____________ Type: New Microwave with Duct Exhaust Fan Labor _______________ Quantity: 1 Permit Fee ____________ BATHROOM EXHAUST FAN: Furnish and install a new 100 CFM exhaust fan with 1 sone or less in the ceiling Remove any attic insulation from around the fixture. The bathroom exhaust fans must have a minimum mechanical exhaust capacity of 50 cfm (cubic feet per minute) when operated intermittently Efficiency and quiet equipment at time of installation completed. Exhaust air from bathrooms must be exhausted directly to the outdoors with bugs screening and cannot be recirculated within the residence or discharged into an attic, crawl space, or other areas inside the building. Securely mounted fan using mechanical fasteners and per manufacturer's specifications so that fan housing does not shake, rattle, or vibrate when operating and, Ensure fan and service disconnect switch are accessible for maintenance according to NEC, or applicable building code Material and methods must meet the requirements of the applicable fire safety code (e.g., thermal or ignition barriers), and comply with Miami-Dade County mechanical building codes regulations and Weatherization Program Guidelines. Labor & Materials maximum allowable cost no more than $400.00 per Bathroom. Follow SWS work specifications. Materials __________ Location: Bathroom 1 Labor ______________ Permit Fees __________ REPLACE WINDOW: Select windows that meet the SHGC, U-value, and air leakage requirements of the work order Select windows that meet the egress and safety glass requirements of the location where they are installed. Select windows that are compatible with their intended surfaces, allow for differential expansion and contraction between dissimilar materials, meet the requirements of the applicable fire safety code (e.g., thermal or ignition barriers), and for use inside the pressure boundary select low volatile organic compound (VOC) sealants that meet independent testing and verification protocols pest-resistant materials that adequately support applied load and are permanent air barriers, materials that meet the requirements of the applicable fire safety code (e.g., thermal or ignition barriers), and low volatile organic compound (VOC) materials for use inside the pressure boundary that meet independent testing and verification protocols. Insulate and seal existing window weight pockets if they remain after new installation Replace any damaged or rotting framing. Verify safe operation and size of egress windows as required by local codes. Remove existing windows and install the new window in accordance with manufacturer specifications in alignment with the wall system's air and thermal boundary. Install flashing to direct water away from the window opening in accordance with manufacturer's instructions. Install flashing per the manufacturer's specifications. Gaps between the new window and existing opening will be sealed with low-expanding foam or equivalent sealant Final installation will be air and watertight. All WORK MUST COMPLY WITH FLORIDA BUILDING CODE IN TERMS OF EGREES. THE CONTRACTOR IS RESPONSIBLE FOR VERIFYING ALL EXISTING WINDOWS OPENINGS FOR SIZES AND EXISTING STRUCTURAL CONDITIONS BEFORE ORDERING AND INSTALLING THE NEW WINDOWS. Materials___________ Location: South Wall 37x50 Labor _____________ Location: North Wall 37x38 Permit Fee ____________ Quantity: 2 REPAIR WINDOW WEATHERTIGHT TO CLOSE PROPERLY: Provide all necessary materials and labor to install replacement any window components, tracks, sashes and tightening adjusting balances any misaligned sashes, tracks, loose hardware, screws on hinges, and handles. Select sealants that are compatible with their intended surfaces, Pest-resistant materials meet the requirements of the applicable fire safety code (e.g. thermal or ignition barriers), and for use inside the pressure boundary select low volatile organic compound (VOC) sealants that meet independent testing and verification. And that meet independent testing and verification protocols. All repair and installation must be according with SWS work specifications (glazing, caulking, sealant, paint, locks, hardware or suitable lubricant to have all designated windows restored and repaired to function as originally intended. Replacing worn weatherstripping and addressing any damaged or broken parts and locking mechanisms etc. Material _____________ Location: In all locations Labor _______________ Quantity: 9 REMOVE AND REPLACE EXTERIOR METAL DOOR: Furnish and install new out-swing impact resistant 1-3/4" pre-hung insulated 6 panel steel entry door with all needed hardware, trim, peep hole and locksets to replace existing doors. Unit to include jamb, keyed entry lock, single cylinder, metal threshold, weather strip, door stopper or safety chain, and door is to swing out with security hinges. Select doors that meet the SHGC, U-value, and air leakage requirements of the work order. Select the correct and safe new doors that meet the safety requirements of the location where they are installed. Doors are required to have a fire-resistance rating, all weather strips and sealants applied to the door will be compatible with the listing of the door materials that meet the requirements of the applicable fire safety code (e.g., thermal or ignition barriers), and low volatile organic compound (VOC) materials for use inside the pressure boundary that meet independent testing and verification protocols. Door replacement and installation must be according with SWS work specifications. • Unit approved by MDC Product Control Division to resist hurricane forces, per the FBC and Miami-Dade Building Code. Doors must have NOA approved by Miami-Dade County and/or FBC approval. Choose the correct and safe new door. • Provide industry standard trim on outside (Brick mold) and inside (Casing mold) Patch stucco surface around door to match existing finish. Paint the door and trim to match the existing paint color and finish. Materials __________ Location: Front Door 36x80 Labor ____________ Location: Rear Door 32x80 Permit Fees _______ Quantity: 2 REPAIR AND SEAL DRYWALL AT UTILTY A/C & W/H HOLES: Repair interior drywall at bathroom ceiling, provides all material and labor necessary to close, patch and match adjacent of the surface area. Repair areas may be, but are not limited to, 1/2", 5/8", GWB, MRGWB, and or Duroc board. Repair the bathroom ceiling, assess the damage, and remove all loose or damaged materials. Then, repair or replace the drywall, sand and smooth the area, prime with a mold moisture-resistant primer. When repairing or replacing ceiling drywall, choose mold moisture-resistant materials. All materials used in weatherization must resist mold and rot if exposed to moisture and humidity. All jobs must meet and be according with SWS work specifications Materials: _____________ Location: Utility Room A/C & W/H Labor ________________ Quantity Approximately: 3 SQFT REPAIR OR REPLACE WATER HEATER PIPE LINES/ JUNCTION BOX /PLACE W/H UP TO CODE The replacement of damaged components, such as corroded wires, loose connectors, or a damaged junction box, will need to be replaced with new, high-quality parts. Ensuring all electrical connections are secure and properly insulated is crucial for safety and proper functionality. Insulate exposed hot and cold-water pipes from water heaters only. Insulate cold water pipes within specified (4) linear feet of heater and all accessible hot water pipes. Repair holes and close, patch any opening surrounding the box inside w/h closet and match adjacent to the surface area of the wall. There should be NO air infiltration or exfiltration inside where W/H resides after repairing. Once the junction box is repaired, it needs to be reassembled and tested to ensure it is functioning correctly and safely. Ensuring the electrical wiring to the water heater is properly connected, safe and compliant with local codes. Ensuring the Junction boxes are securely covered with appropriate, durable covers. Enclose all wiring splices inside a location-appropriate (e.g. wet-location, outdoor, indoor, etc.) UL listed electrical enclosure per the NEC. Wiring splices are safely enclosed in appropriate enclosure in compliance with applicable code (e.g., NFPA 70, IRC, IBC, IMC) and manufacturer specifications. Ensure proper installation Temperature and pressure relief valve will be installed in compliance with IRC, HUD code, County code and according to manufacturer specifications Materials: _____________ Location: W/H Closet Labor ________________ Estimated Quantity: 3 SQFT ATTIC HATCH INSTALL FOAM &TAPE : A. Build or Install a dam around the attic hatch opening to maintain the full level of ceiling insulation to the edge of the opening and to prevent insulation from falling into living space. Frame the opening with dimension lumber, OSB, or plywood. Don’t use cardboard or foam board to dam around access hatches. (Must use plywood or other durable rigid material) Cardboard and foam board aren’t durable materials where they are readily accessible to occupants. Repair or replace the attic door cover if damaged. B. Install foam board in layers to the attic door and secure by gluing the foam to prevent heat transfer through the access door using construction adhesive to achieve R-30 or the greatest attainable R-value that still allows the door to function. Permanently attaches weatherstripping around the entire perimeter of attic-access door on frame to create an effective air seal between the door frame and the door. There shouldn’t be air infiltration in the surrounding of the attic door entrance. Select low volatile organic compound (VOC) sealants that meet independent testing and verification protocols methods. All jobs must meet and be according with SWS work specifications. Materials_____________ Location: Hallway Labor________________ INSTALL ENERGY RECOVERY VENTILATOR: Select Energy Recovery Ventilators (ERV) that are ENERGY STAR®, equivalent, or better. Select efficient equipment. This whole building ventilation must be installed in a dwelling unit to provide indoor air quality that is acceptable to human occupants. Ventilator requirements are 40 to 50 CFM's continuous flow and a rating of 1 zone or less. Contractors must follow program requirement and information provided by the ASHRAE 62.2 VENTILATION CFM rate. Install all electrical wiring according to the manufacturer specifications and applicable code. All installation terminations: per manufacturer's specifications and applicable code, All jobs must meet and be according with SWS work specifications. The ducts must vent directly to the outdoors with bugs screening (Through an insulated duct to gable or wall) never into the attic or into other locations within the home. Materials and methods must comply with Miami-Dade County regulations and Weatherization Program Guidelines. Building Permit must be separate from other ventilation permits. Materials _____________ Location: Hallway Labor ________________ Permit Fees ____________ Subtotal Materials: _____________ Subtotal Labor: ________________ Subtotal Permit Fees:___________ TOTAL PROJECT COST: ________ Scope of Work 2 Pages 1 - 8 Folio # 30-6923-004-1810 Work Site Address: 13113 SW 243 Street INSTALL SMOKE DETECTORS: Furnish and install battery-operated smoke alarms that are listed and labeled in accordance with UL 217 and have sealed, non-replaceable, 10-year batteries along with a tamper proof cover is required. Install battery-operated smoke alarms in the locations required by the Authority Having Jurisdiction (AHJ) Install battery-operated smoke alarms in accordance with the manufacturer's instructions and Miami Dade residential code. Materials_____________ Locations: In All Locations needed Labor________________ Quantity:4 INSTALL CO DETECTOR: Furnish and install CO alarms (Carbon Monoxide Detector) that are listed and labeled in accordance with UL 2034, or approved by the authority having jurisdiction, and have a minimum of: 10-year manufacturer's warranty Contain internal non-replaceable batteries along with tamper proof covering near gas appliances. Install CO alarms in the locations required by the Authority Having Jurisdiction (AHJ) Install CO alarms in accordance with the manufacturer's instructions The installed location must not interfere with or obstruct any cabinet or drawer functions. aterials_______________ Location: Hallway Sleeping Room Area Labor__________________ Quantity: 1 PROVIDE A/C AIR FILTER: Remove and replace disposable pleated AC filter with filtration must meet a minimum efficiency of MERV 8 or better and leave the extra with homeowner. Filter opening must allow filter to be fully removed and inserted without bending or damaging the filter Materials______________ Quantity: 2 INSTALL AERATORS: Furnish and install Faucet aerators with a flow rate of 2.2 GPM or less, constructed of solid brass with polished chrome finish. Maximum flow rate of 2.2 GPM (gallons per minute) Kitchen must be swiveling type with multi spray. Faucet aerators will be tested to determine if equipment is tightened adequately to prevent leakage at the point of connection. Materials ______________ Quantity: 2 Labor _________________ Locations: In All Locations PROVIDE LED LIGHT BULBS: Furnish new Energy Star certified LED bulbs, and replace incandescent light lighting level quality required for the intended application (e.g., task lighting, hazards lighting, nightlights) is the highest level of efficiency within a technology (e.g., LED bulbs) are ENERGY STAR® qualified, equivalent or better, and UL approved Install lighting in accordance with manufacturer specifications and applicable code (i.e., NFPA 70, NFPA 101, NECA/IESNA 500) If applicable, clean the lens and reflector before installing new bulb Safe and proper installation. Permanently remove old products from job sites and recycle or dispose of in accordance with local and federal law (e.g., EPA Section 608 of Clean Air Act of 1990) Materials _________________ Quantity 12 INSTALL SHOWER HEADS: Furnish and install, low-flow Showerhead made of ABS thermoplastic with Chrome-plated finish, self-cleaning and maintenance free, non-removable flow compensator. rated for 2.5 gallons per minute (GPM) or less that includes an antiscald valve. If multiple heads are provided in a shower stall, the total flow rate may not exceed 2.5 GPM. The showerhead will be tested to determine if equipment is tightened adequately to prevent leakage at the point of connection Materials ______________ Quantity: 1 Labor _________________ INSTALL BATHROOM EXHAUST FAN: Furnish and install a new 100 CFM exhaust fan with 1 sone or less in the ceiling Remove any attic insulation from around the fixture. The bathroom exhaust fans must have a minimum mechanical exhaust capacity of 50 cfm (cubic feet per minute) when operated intermittently Efficiency and quiet equipment at time of installation completed. Exhaust air from bathrooms must be exhausted directly to the outdoors with bugs screening and cannot be recirculated within the residence or discharged into an attic, crawl space, or other areas inside the building. Securely mounted fan using mechanical fasteners and per manufacturer's specifications so that fan housing does not shake, rattle, or vibrate when operating and, Ensure fan and service disconnect switch are accessible for maintenance according to NEC, or applicable building code Material and methods must meet the requirements of the applicable fire safety code (e.g., thermal or ignition barriers) and comply with Miami-Dade County mechanical building codes regulations and Weatherization Program Guidelines. Labor & Materials maximum allowable cost $400.00 per Bathroom. Follow SWS work specifications. Materials __________ Location: Bathroom 1 Labor ______________ Permit Fee ____________ STOVE OR HOOD VENTILATION: Furnish and install HOOD mechanical ventilation for the kitchen exhaust fan as follows: Labor & Materials maximum allowable cost $300.00. • Install flexible duct attached from ranged hood to exterior of the residence • All venting exhaust must be ducted and expelled to the outside Materials _____________ Location: KITCHEN Labor _______________ Type: Hood MAKE A NEW ATTIC HATCH: A. Build or Install a dam around the attic hatch opening to maintain the full level of ceiling insulation to the edge of the opening and to prevent insulation from falling into living space. Frame the opening with dimension lumber, OSB, or plywood. Don’t use cardboard or foam board to dam around access hatches. (Must use plywood or other durable rigid material) Cardboard and foam board aren’t durable materials where they are readily accessible to occupants. Repair or replace the attic door cover if damaged. B. Install foam board in layers to the attic door and secure by gluing the foam to prevent heat transfer through the access door using construction adhesive to achieve R-30 or the greatest attainable R-value that still allows the door to function. Permanently attaches weatherstripping around the entire perimeter of attic-access door on frame to create an effective air seal between the door frame and the door. There shouldn’t be air infiltration in the surrounding of the attic door entrance. Select low volatile organic compound (VOC) sealants that meet independent testing and verification protocols methods. All jobs must meet and be according with SWS work specifications. Materials_____________ Location: _______________ Labor________________ REMOVE AND REPLACE EXTERIOR METAL DOOR: Furnish and install new out-swing impact resistant 1-3/4" pre-hung insulated 6 panel steel entry door with all needed hardware, trim, peep hole and locksets to replace existing doors. Unit to include jamb, keyed entry lock, single cylinder, metal threshold, weather strip, door stopper or safety chain, and door is to swing out with security hinges. Select doors that meet the SHGC, U-value, and air leakage requirements of the work order. Select the correct and safe new doors that meet the safety requirements of the location where they are installed. Doors are required to have a fire-resistance rating, all weather strips and sealants applied to the door will be compatible with the listing of the door materials that meet the requirements of the applicable fire safety code (e.g., thermal or ignition barriers), and low volatile organic compound (VOC) materials for use inside the pressure boundary that meet independent testing and verification protocols. Door replacement and installation must be according with SWS work specifications. • Unit approved by MDC Product Control Division to resist hurricane forces, per the FBC and Miami-Dade Building Code. Doors must have NOA approved by Miami-Dade County and/or FBC approval. Choose the correct and safe new door. Provide industry standard trim on outside (Brick mold) and inside (Casing mold) Patch stucco surface around door to match existing finish. Paint the door and trim to match the existing paint color and finish. The Contractor is responsible to verify the correct size of the doors. Materials __________ Location: Front Door / Side Door Labor ____________ Size: 36x80 Permit Fees _______ Quantity: 2 INSTALL FULL LOUVER DOOR AT A/H CLOSET: Furnish and Install material and labor for full louver wood bifold at AC handler closet. Provide all necessary hardware and finish matching adjacent areas. The Contractor is responsible to verify the correct size the door. Materials_______________ Location: A/C closet Labor __________________ Estimated Size: 32x80 REPLACE WATER HEATER: Furnish and install water heating unit that: has an Energy Factor (EF) of 0.93 or better fits in the installation space with the required clearances and provides sufficient hot water for the home and occupants. Select efficient and properly sized water heater. If appliance is installed in or above conditioned space or in a location where water damage could occur, install a drain pan according to the requirements of the IRC Drain pan to the exterior of the building to prevent water damage from leaking water. Install water heater in compliance with applicable code e.g., NFPA 70, IRC, IBC, IMC) and manufacturer specifications and safe installation. Ensure that anode rod is accessible for replacement Ensure the appliance can be easily maintained and replaced. Temperature and Pressure (TandP) relief valve per the IRC and manufacturer specifications Select piping material based on IRC requirements. Select durable and correctly sized pipe insulation that: is a minimum of R-3 is a vapor retarder is the correct interior diameter to match pipes is UV-protected if installed outside. Safe, continuous, and durable installation. Electrical connection must be upgraded to manufacturers’ recommendation and Florida Building Code and/or any applicable Miami-Dade County Building Codes. All jobs must meet and be according with SWS work specifications. Permanently remove equipment from job site and recycle or dispose of removed equipment and refrigerant in accordance with local and federal law (e.g., EPA Section 608 of Clean Air Act of 1990) Old equipment is permanently decommission removed from service, protect the environment, and comply with regulations. The Contractors is responsible to verify the water heater size. Materials ___________ Labor ____________ Type: Tank less W/H Permit Fees __________ Disposal Fee ________ INSTALL ENERGY RECOVERY VENTILATOR: Select Energy Recovery Ventilators (ERV) that are ENERGY STAR®, equivalent, or better. Select efficient equipment. This whole building ventilation must be installed in a dwelling unit to provide indoor air quality that is acceptable to human occupants. Ventilator requirements are 40 to 50 CFM's continuous flow and a rating of 1 zone or less. Contractors must follow program requirement and information provided by the ASHRAE 62.2 VENTILATION CFM rate. Install all electrical wiring according to the manufacturer specifications and applicable code. All installation terminations: per manufacturer's specifications and applicable code, All jobs must meet and be according with SWS work specifications. The ducts must vent directly to the outdoors with bugs screening (Through an insulated duct to gable or wall) never into the attic or into other locations within the home. Materials and methods must comply with Miami-Dade County regulations and Weatherization Program Guidelines. Important: Building Permit must be separate from other ventilation permits. Materials _____________ Location ____________ Labor ________________ Permit Fees ____________ REPLACE ELECTRICAL RECEPTACLE: Furnish and install necessary labor and material for the repair or replacement of receptacle to work properly. Materials_________________ Locations: Entrance front door area Labor____________________ Quantity:1 Subtotal Materials: _____________ Subtotal Labor: ________________ Subtotal Permit Fees:___________ TOTAL PROJECT COST: ________ Scope of Work 3 Pages 1 - 7 Folio # 30-6923-004-1480 Work Site Address: 13120 SW 243 Terrace INSTALL SMOKE DETECTORS: Furnish and install battery-operated smoke alarms that are listed and labeled in accordance with UL 217 and have sealed, non-replaceable, 10-year batteries along with a tamper proof cover is required. Install battery-operated smoke alarms in the locations required by the Authority Having Jurisdiction (AHJ) Install battery-operated smoke alarms in accordance with the manufacturer's instructions and Miami Dade residential code. Materials_____________ Locations: In All Locations needed Labor________________ Quantity:4 INSTALL CO DETECTOR: Furnish and install CO alarms (Carbon Monoxide Detector) that are listed and labeled in accordance with UL 2034, or approved by the authority having jurisdiction, and have a minimum of: 10-year manufacturer's warranty Contain internal non-replaceable batteries along with tamper proof covering near gas appliances. Install CO alarms in the locations required by the Authority Having Jurisdiction (AHJ) Install CO alarms in accordance with the manufacturer's instructions The installed location must not interfere with or obstruct any cabinet or drawer functions. Materials_______________ Location: Hallway Sleeping Room Area Labor__________________ Quantity: 1 INSTALL AERATORS: Furnish and install Faucet aerators with a flow rate of 2.2 GPM or less, constructed of solid brass with polished chrome finish. Maximum flow rate of 2.2 GPM (gallons per minute) Kitchen must be swiveling type with multi spray. Faucet aerators will be tested to determine if equipment is tightened adequately to prevent leakage at the point of connection. Materials ______________ Quantity: 2 Labor _________________ Locations: In All Locations PROVIDE A/C AIR FILTER: Remove and replace disposable pleated AC filter with filtration must meet a minimum efficiency of MERV 8 or better and leave the extra with homeowner. Filter opening must allow filter to be fully removed and inserted without bending or damaging the filter Materials______________ Quantity: 2 PROVIDE LED LIGHT BULBS: Furnish new Energy Star certified LED bulbs, and replace incandescent light lighting level quality required for the intended application (e.g., task lighting, hazards lighting, nightlights) is the highest level of efficiency within a technology (e.g., LED bulbs) are ENERGY STAR® qualified, equivalent or better, and UL approved Install lighting in accordance with manufacturer specifications and applicable code (i.e., NFPA 70, NFPA 101, NECA/IESNA 500) If applicable, clean the lens and reflector before installing new bulb Safe and proper installation. Permanently remove old products from job sites and recycle or dispose of in accordance with local and federal law (e.g., EPA Section 608 of Clean Air Act of 1990) Materials _________________ Quantity 12 Labor ____________________ Location: In All Locations STOVE OR HOOD VENTILATION: Furnish and install HOOD mechanical ventilation for the kitchen exhaust fan as follows: Labor & Materials maximum allowable cost $300.00. • Install flexible duct attached from ranged hood to exterior of the residence • All venting exhaust must be ducted and expelled to the outside Materials _____________ Location: KITCHEN Labor _______________ Type: Hood BATHROOM EXHAUST FAN: Furnish and install a new 100 CFM exhaust fan with 1 sone or less in the ceiling Remove any attic insulation from around the fixture. The bathroom exhaust fans must have a minimum mechanical exhaust capacity of 50 cfm (cubic feet per minute) when operated intermittently Efficiency and quiet equipment at time of installation completed. Exhaust air from bathrooms must be exhausted directly to the outdoors with bugs screening and cannot be recirculated within the residence or discharged into an attic, crawl space, or other areas inside the building. Securely mounted fan using mechanical fasteners and per manufacturer's specifications so that fan housing does not shake, rattle, or vibrate when operating and, Ensure fan and service disconnect switch are accessible for maintenance according to NEC, or applicable building code Material and methods must meet the requirements of the applicable fire safety code (e.g., thermal or ignition barriers), and comply with Miami-Dade County mechanical building codes regulations and Weatherization Program Guidelines. Labor & Materials maximum allowable cost $400.00 per Bathroom. Follow SWS work specifications. Materials __________ Location: Bathroom 1 Labor ______________ Permit Fees __________ INSTALL SHOWER HEADS: Furnish and install, low-flow Showerhead made of ABS thermoplastic with Chrome-plated finish, self-cleaning and maintenance free, non-removable flow compensator. rated for 2.5 gallons per minute (GPM) or less that includes an antiscald valve. If multiple heads are provided in a shower stall, the total flow rate may not exceed 2.5 GPM. The showerhead will be tested to determine if equipment is tightened adequately to prevent leakage at the point of connection Materials ______________ Quantity: 1 Labor _________________ REMOVE AND REPLACE EXTERIOR METAL DOOR: Furnish and install new out-swing impact resistant 1-3/4" pre-hung insulated 6 panel steel entry door with all needed hardware, trim, peep hole and locksets to replace existing doors. Unit to include jamb, keyed entry lock, single cylinder, metal threshold, weather strip, door stopper or safety chain, and door is to swing out with security hinges. Select doors that meet the SHGC, U-value, and air leakage requirements of the work order. Select the correct and safe new doors that meet the safety requirements of the location where they are installed. Doors are required to have a fire-resistance rating, all weather strips and sealants applied to the door will be compatible with the listing of the door materials that meet the requirements of the applicable fire safety code (e.g., thermal or ignition barriers), and low volatile organic compound (VOC) materials for use inside the pressure boundary that meet independent testing and verification protocols. Door replacement and installation must be according with SWS work specifications. • Unit approved by MDC Product Control Division to resist hurricane forces, per the FBC and Miami-Dade Building Code. Doors must have NOA approved by Miami-Dade County and/or FBC approval. Choose the correct and safe new door. • Provide industry standard trim on outside (Brick mold) and inside (Casing mold) Patch stucco surface around door to match existing finish. Paint the door and trim to match the existing paint color and finish. Materials __________ Location: Front Door 36x80 Labor ____________ Location : Side Door 36x80 Permit Fees _______ Quantity: 2 REPAIR &INSTALL BAT, BLOKING INSULATION & FOAM TAPE AROUND HATCH AT EXISTING ATTIC HATCH: A. Build or Install a dam around the attic hatch opening to maintain the full level of ceiling insulation to the edge of the opening and to prevent insulation from falling into living space. Frame the opening with dimension lumber, OSB, or plywood. Don’t use cardboard or foam board to dam around access hatches. (Must use plywood or other durable rigid material) Cardboard and foam board aren’t durable materials where they are readily accessible to occupants. Repair or replace the attic door cover if damaged. B. Install foam board in layers to the attic door and secure by gluing the foam to prevent heat transfer through the access door using construction adhesive to achieve R-30 or the greatest attainable R-value that still allows the door to function. Permanently attaches weatherstripping around the entire perimeter of attic-access door on frame to create an effective air seal between the door frame and the door. There shouldn’t be air infiltration in the surrounding of the attic door entrance. Select low volatile organic compound (VOC) sealants that meet independent testing and verification protocols methods. All jobs must meet and be according with SWS work specifications. Materials_____________ Location: Utility Room Labor________________ REPLACE WATER HEATER: Furnish and install water heating unit that: has an Energy Factor (EF) of 0.93 or better fits in the installation space with the required clearances and provides sufficient hot water for the home and occupants. Select efficient and properly sized water heater. If appliance is installed in or above conditioned space or in a location where water damage could occur, install a drain pan according to the requirements of the IRC Drain pan to the exterior of the building to prevent water damage from leaking water. Install water heater in compliance with applicable code e.g., NFPA 70, IRC, IBC, IMC) and manufacturer specifications and safe installation. Ensure that anode rod is accessible for replacement Ensure the appliance can be easily maintained and replaced. Temperature and Pressure (TandP) relief valve per the IRC and manufacturer specifications Select piping material based on IRC requirements. Select durable and correctly sized pipe insulation that: is a minimum of R-3 is a vapor retarder is the correct interior diameter to match pipes is UV-protected if installed outside. Safe, continuous, and durable installation. Electrical connection must be upgraded to manufacturers’ recommendation and Florida Building Code and/or any applicable Miami-Dade County Building Codes. All jobs must meet and be according with SWS work specifications. Permanently remove equipment from job site and recycle or dispose of removed equipment and refrigerant in accordance with local and federal law (e.g., EPA Section 608 of Clean Air Act of 1990) Old equipment is permanently decommission removed from service, protect the environment, and comply with regulations. Materials ___________ Size: 40 Gal Labor ______________ Type: Storage W/H Permit Fees __________ Disposal Fee ________ INSTALL ENERGY RECOVERY VENTILATOR: Select Energy Recovery Ventilators (ERV) that are ENERGY STAR®, equivalent, or better. Select efficient equipment. This whole building ventilation must be installed in a dwelling unit to provide indoor air quality that is acceptable to human occupants. Ventilator requirements are 40 to 50 CFM's continuous flow and a rating of 1 zone or less. Contractors must follow program requirement and information provided by the ASHRAE 62.2 VENTILATION CFM rate. Install all electrical wiring according to the manufacturer specifications and applicable code. All installation terminations: per manufacturer's specifications and applicable code, All jobs must meet and be according with SWS work specifications. The ducts must vent directly to the outdoors with bugs screening (Through an insulated duct to gable or wall) never into the attic or into other locations within the home. Materials and methods must comply with Miami-Dade County regulations and Weatherization Program Guidelines. Building Permit must be separate from other ventilation permits. Materials _____________ Location: Hallway Labor ________________ Permit Fees ____________ Subtotal Materials: _____________ Subtotal Labor: ________________ Subtotal Permit Fees:___________ TOTAL PROJECT COST: ________ Scope of Work 4 Pages 1 - 8 Folio # 30-6923-004-1250 Work Site Address: 12943 SW 243 Street INSTALL SMOKE DETECTORS: Furnish and install battery-operated smoke alarms that are listed and labeled in accordance with UL 217 and have sealed, non-replaceable, 10-year batteries along with a tamper proof cover is required. Install battery-operated smoke alarms in the locations required by the Authority Having Jurisdiction (AHJ) Install battery-operated smoke alarms in accordance with the manufacturer's instructions and Miami Dade residential code. Materials_____________ Locations: In All Locations needed Labor________________ Quantity:4 INSTALL CO DETECTOR: Furnish and install CO alarms (Carbon Monoxide Detector) that are listed and labeled in accordance with UL 2034, or approved by the authority having jurisdiction, and have a minimum of: 10-year manufacturer's warranty Contain internal non-replaceable batteries along with tamper proof covering near gas appliances. Install CO alarms in the locations required by the Authority Having Jurisdiction (AHJ) Install CO alarms in accordance with the manufacturer's instructions The installed location must not interfere with or obstruct any cabinet or drawer functions. Materials_______________ Location: Hallway Sleeping Room Area Labor__________________ Quantity: 1 PROVIDE A/C AIR FILTER: Remove and replace disposable pleated AC filter with filtration must meet a minimum efficiency of MERV 8 or better and leave the extra with homeowner. Filter opening must allow filter to be fully removed and inserted without bending or damaging the filter Materials______________ Quantity: 2 PROVIDE LED LIGHT BULBS: Furnish new Energy Star certified LED bulbs, and replace incandescent light lighting level quality required for the intended application (e.g., task lighting, hazards lighting, nightlights) is the highest level of efficiency within a technology (e.g., LED bulbs) are ENERGY STAR® qualified, equivalent or better, and UL approved Install lighting in accordance with manufacturer specifications and applicable code (i.e., NFPA 70, NFPA 101, NECA/IESNA 500) If applicable, clean the lens and reflector before installing new bulb Safe and proper installation. Permanently remove old products from job sites and recycle or dispose of in accordance with local and federal law (e.g., EPA Section 608 of Clean Air Act of 1990) Materials _________________ Quantity 12 Labor ____________________ Location: In All Locations REPLACE BATHROOM EXHAUST FAN: Furnish and install a new 100 CFM exhaust fan with 1 sone or less in the ceiling Remove any attic insulation from around the fixture. The bathroom exhaust fans must have a minimum mechanical exhaust capacity of 50 cfm (cubic feet per minute) when operated intermittently Efficiency and quiet equipment at time of installation completed. Exhaust air from bathrooms must be exhausted directly to the outdoors with bugs screening and cannot be recirculated within the residence or discharged into an attic, crawl space, or other areas inside the building. Securely mounted fan using mechanical fasteners and per manufacturer's specifications so that fan housing does not shake, rattle, or vibrate when operating and, Ensure fan and service disconnect switch are accessible for maintenance according to NEC, or applicable building code Material and methods must meet the requirements of the applicable fire safety code (e.g., thermal or ignition barriers), and comply with Miami-Dade County mechanical building codes regulations and Weatherization Program Guidelines. Labor & Materials maximum allowable cost $400.00 per Bathroom. Follow SWS work specifications. Materials __________ Location: Bath 1 Labor _____________ STOVE OR HOOD VENTILATION: Furnish and install HOOD mechanical ventilation for the kitchen exhaust fan as follows: Labor & Materials maximum allowable cost $300.00. • Install flexible duct attached from ranged hood to exterior of the residence • All venting exhaust must be ducted and expelled to the outside Materials _____________ Location: KITCHEN Labor _______________ Type: Hood DRYER VENTILATION: Select dryer transition ducting materials that are UL 2158A approved and less than 8 feet in total length with no joints. Select primary dryer ducting material that is 28-gauge metal with a smooth interior Smooth airflow that does not collect lint be UL approved for dryers be installed according to manufacturer specifications be airtight when dryer is operating Safe and airtight lint collection. Vent all clothes dryers outdoors, install a dryer booster fan that is listed and labeled to UL 705 for dryer ducts exceeding 35' in equivalent length. Install ducts according SWS work specifications detail for "Ventilation Ducts” Dryer ducted too outdoors durably and effectively. If a lint collection device is installed, it must: be UL approved, for dryers to be installed according to manufacturer specifications be airtight when dryer is operating. Safe and airtight lint collection. Vent dryer through a termination manufactured for use with dryers that include a backdraft damper. Follow SWS work specifications. Dryer termination is effective, safe and does not inhibit flow. Seal all duct connections with 181B or 181B-M listed material Airtight ducts Materials ___________ Location: Utility Room Labor ______________ Type: Make New REMOVE AND REPLACE EXTERIOR METAL DOOR: Furnish and install new out-swing impact resistant 1-3/4" pre-hung insulated 6 panel steel entry door with all needed hardware, trim, peep hole and locksets to replace existing doors. Unit to include jamb, keyed entry lock, single cylinder, metal threshold, weather strip, door stopper or safety chain, and door is to swing out with security hinges. Select doors that meet the SHGC, U-value, and air leakage requirements of the work order. Select the correct and safe new doors that meet the safety requirements of the location where they are installed. Doors are required to have a fire-resistance rating, all weather strips and sealants applied to the door will be compatible with the listing of the door materials that meet the requirements of the applicable fire safety code (e.g., thermal or ignition barriers), and low volatile organic compound (VOC) materials for use inside the pressure boundary that meet independent testing and verification protocols. Door replacement and installation must be according with SWS work specifications. • Unit approved by MDC Product Control Division to resist hurricane forces, per the FBC and Miami-Dade Building Code. Doors must have NOA approved by Miami-Dade County and/or FBC approval. Choose the correct and safe new door. • Provide industry standard trim on outside (Brick mold) and inside (Casing mold) Patch stucco surface around door to match existing finish. Paint the door and trim to match the existing paint color and finish. Materials __________ Location: Front Door / Side Door Labor ____________ Size: 36x80 Permit Fees _______ Quantity: 2 REPLACE WATER HEATER: Furnish and install water heating unit that: has an Energy Factor (EF) of 0.93 or better fits in the installation space with the required clearances and provides sufficient hot water for the home and occupants. Select efficient and properly sized water heater. If appliance is installed in or above conditioned space or in a location where water damage could occur, install a drain pan according to the requirements of the IRC Drain pan to the exterior of the building to prevent water damage from leaking water. Install water heater in compliance with applicable code e.g., NFPA 70, IRC, IBC, IMC) and manufacturer specifications and safe installation. Ensure that anode rod is accessible for replacement Ensure the appliance can be easily maintained and replaced. Temperature and Pressure (TandP) relief valve per the IRC and manufacturer specifications Select piping material based on IRC requirements. Select durable and correctly sized pipe insulation that: is a minimum of R-3 is a vapor retarder is the correct interior diameter to match pipes is UV-protected if installed outside. Safe, continuous, and durable installation. Electrical connection must be upgraded to manufacturers’ recommendation and Florida Building Code and/or any applicable Miami-Dade County Building Codes. All jobs must meet and be according with SWS work specifications. Permanently remove equipment from job site and recycle or dispose of removed equipment and refrigerant in accordance with local and federal law (e.g., EPA Section 608 of Clean Air Act of 1990) Old equipment is permanently decommission removed from service, protect the environment, and comply with regulations. Materials ___________ Size: 40 Gal Labor ______________ Type: Storage W/H Permit Fees __________ Disposal Fee ________ REPLACE REFRIGERATOR: Furnish and install the New Energy STAR Refrigerator with proper measurements to fit in the current location. Old Equipment must be hauled away and de-manufactured through removal off the grid and completion/receipt of the de-manufacturing certificate as signed by the owner of the residence and the vendor. Include the ice line and connection there of (a separate line item for disposal fees MUST BE included on the invoice) Materials _________________ Cubic feet: 21 C/F Labor ____________________ Type: Top Freezer/ Not Ice Maker Disposal Fee ______________ REPAIR EXISTING ATTIC HATCH INSTALL FOAM BOARD AND FOAM TAPE A. Build or Install a dam around the attic hatch opening to maintain the full level of ceiling insulation to the edge of the opening and to prevent insulation from falling into living space. Frame the opening with dimension lumber, OSB, or plywood. Don’t use cardboard or foam board to dam around access hatches. (Must use plywood or other durable rigid material) Cardboard and foam board aren’t durable materials where they are readily accessible to occupants. Repair or replace the attic door cover if damaged. B. Install foam board in layers to the attic door and secure by gluing the foam to prevent heat transfer through the access door using construction adhesive to achieve R-30 or the greatest attainable R-value that still allows the door to function. Permanently attaches weatherstripping around the entire perimeter of attic-access door on frame to create an effective air seal between the door frame and the door. There shouldn’t be air infiltration in the surrounding of the attic door entrance. Select low volatile organic compound (VOC) sealants that meet independent testing and verification protocols methods. All jobs must meet and be according with SWS work specifications. Materials_____________ Location: Utility Labor________________ Type: Repair Existing INSTALL ENERGY RECOVERY VENTILATOR: Select Energy Recovery Ventilators (ERV) that are ENERGY STAR®, equivalent, or better. Select efficient equipment. This whole building ventilation must be installed in a dwelling unit to provide indoor air quality that is acceptable to human occupants. Ventilator requirements are 40 to 50 CFM's continuous flow and a rating of 1 zone or less. Contractors must follow program requirement and information provided by the ASHRAE 62.2 VENTILATION CFM rate. Install all electrical wiring according to the manufacturer specifications and applicable code. All installation terminations: per manufacturer's specifications and applicable code, All jobs must meet and be according with SWS work specifications. The ducts must vent directly to the outdoors with bugs screening (Through an insulated duct to gable or wall) never into the attic or into other locations within the home. Materials and methods must comply with Miami-Dade County regulations and Weatherization Program Guidelines. Building Permit must be separate from other ventilation permits. Materials _____________ Location: Hallway Labor ________________ Permit Fees ____________ Subtotal Materials: _____________ Subtotal Labor: ________________ Subtotal Permit Fees:___________ TOTAL PROJECT COST: ________ Scope of Work 5 Pages 1 - 7 Folio # 30-6923-004-1860 Work Site Address: 24263 SW 131 Avenue INSTALL SMOKE DETECTORS: Furnish and install battery-operated smoke alarms that are listed and labeled in accordance with UL 217 and have sealed, non-replaceable, 10-year batteries along with a tamper proof cover is required. Install battery-operated smoke alarms in the locations required by the Authority Having Jurisdiction (AHJ) Install battery-operated smoke alarms in accordance with the manufacturer's instructions and Miami Dade residential code. Materials_____________ Locations: In All Locations needed Labor________________ Quantity:4 INSTALL CO DETECTOR: Furnish and install CO alarms (Carbon Monoxide Detector) that are listed and labeled in accordance with UL 2034, or approved by the authority having jurisdiction, and have a minimum of: 10-year manufacturer's warranty Contain internal non-replaceable batteries along with tamper proof covering near gas appliances. Install CO alarms in the locations required by the Authority Having Jurisdiction (AHJ) Install CO alarms in accordance with the manufacturer's instructions The installed location must not interfere with or obstruct any cabinet or drawer functions. Materials_______________ Location: Hallway Sleeping Room Area Labor__________________ Quantity: 1 PROVIDE A/C AIR FILTER: Remove and replace disposable pleated AC filter with filtration must meet a minimum efficiency of MERV 8 or better and leave the extra with homeowner. Filter opening must allow filter to be fully removed and inserted without bending or damaging the filter Materials______________ Quantity: 2 PROVIDE LED LIGHT BULBS: Furnish new Energy Star certified LED bulbs, and replace incandescent light lighting level quality required for the intended application (e.g., task lighting, hazards lighting, nightlights) is the highest level of efficiency within a technology (e.g., LED bulbs) are ENERGY STAR® qualified, equivalent or better, and UL approved Install lighting in accordance with manufacturer specifications and applicable code (i.e., NFPA 70, NFPA 101, NECA/IESNA 500) If applicable, clean the lens and reflector before installing new bulb Safe and proper installation. Permanently remove old products from job sites and recycle or dispose of in accordance with local and federal law (e.g., EPA Section 608 of Clean Air Act of 1990) Materials _________________ Quantity 12 Labor ____________________ Location: BATHROOM EXHAUST FAN: Furnish and install a new 100 CFM exhaust fan with 1 sone or less in the ceiling Remove any attic insulation from around the fixture. The bathroom exhaust fans must have a minimum mechanical exhaust capacity of 50 cfm (cubic feet per minute) when operated intermittently Efficiency and quiet equipment at time of installation completed. Exhaust air from bathrooms must be exhausted directly to the outdoors with bugs screening and cannot be recirculated within the residence or discharged into an attic, crawl space, or other areas inside the building. Securely mounted fan using mechanical fasteners and per manufacturer's specifications so that fan housing does not shake, rattle, or vibrate when operating and, Ensure fan and service disconnect switch are accessible for maintenance according to NEC, or applicable building code Material and methods must meet the requirements of the applicable fire safety code (e.g., thermal or ignition barriers), and comply with Miami-Dade County mechanical building codes regulations and Weatherization Program Guidelines. Labor & Materials maximum allowable cost $400.00 per Bathroom. Follow SWS work specifications. Materials __________ Location: Bath 1 Labor ______________ Type: Replace Existing Permit Fees __________ STOVE OR HOOD VENTILATION: Furnish and install HOOD mechanical ventilation for the kitchen exhaust fan as follows: Labor & Materials maximum allowable cost $300.00. • Install flexible duct attached from ranged hood to exterior of the residence • All venting exhaust must be ducted and expelled to the outside Materials _____________ Location: KITCHEN Labor _______________ Type: Hood INSTALL AERATORS: • Furnish and install Faucet aerator, constructed of solid brass with polished chrome finish. Maximum flow rate of 2.2 GPM (gallons per minute) Kitchen must be swiveling type with multi spray. • Faucet aerators will be tested to determine if equipment is tightened adequately to prevent leakage at the point of connection. Materials ______________ Quantity: 2 Labor ________________ Locations: Kitchen & Bath # 1 REMOVE AND REPLACE EXTERIOR METAL DOOR: Furnish and install new out-swing impact resistant 1-3/4" pre-hung insulated 6 panel steel entry door with all needed hardware, trim, peep hole and locksets to replace existing doors. Unit to include jamb, keyed entry lock, single cylinder, metal threshold, weather strip, door stopper or safety chain, and door is to swing out with security hinges. Select doors that meet the SHGC, U-value, and air leakage requirements of the work order. Select the correct and safe new doors that meet the safety requirements of the location where they are installed. Doors are required to have a fire-resistance rating, all weather strips and sealants applied to the door will be compatible with the listing of the door materials that meet the requirements of the applicable fire safety code (e.g., thermal or ignition barriers), and low volatile organic compound (VOC) materials for use inside the pressure boundary that meet independent testing and verification protocols. Door replacement and installation must be according with SWS work specifications. • Unit approved by MDC Product Control Division to resist hurricane forces, per the FBC and Miami-Dade Building Code. Doors must have NOA approved by Miami-Dade County and/or FBC approval. Choose the correct and safe new door. • Provide industry standard trim on outside (Brick mold) and inside (Casing mold) Patch stucco surface around door to match existing finish. Paint the door and trim to match the existing paint color and finish. Materials __________ Location: Front Door/ Side Door Labor ____________ Size: 36 x 80 Permit Fees _______ Quantity: 2 INSTALL INSULATION & FOAM TAPE TO ATTIC HATCH: A. Build or Install a dam around the attic hatch opening to maintain the full level of ceiling insulation to the edge of the opening and to prevent insulation from falling into living space. Frame the opening with dimension lumber, OSB, or plywood. Don’t use cardboard or foam board to dam around access hatches. (Must use plywood or other durable rigid material) Cardboard and foam board aren’t durable materials where they are readily accessible to occupants. Replace the attic door cover if damaged. B. Install foam board in layers to the attic door and secure by gluing the foam to prevent heat transfer through the access door using construction adhesive to achieve R-30 or the greatest attainable R-value that still allows the door to function. Permanently attaches weatherstripping around the entire perimeter of attic-access door on frame to create an effective air seal between the door frame and the door. There shouldn’t be air infiltration in the surrounding of the attic door entrance. Select low volatile organic compound (VOC) sealants that meet independent testing and verification protocols methods. All jobs must meet and be according with SWS work specifications. Materials_____________ Location: Utility Labor________________ INSTALL FULL LOUVER DOOR AT A/H CLOSET: Furnish and Install material and labor for full louver wood bifold at AC handler closet. Provide all necessary hardware and finish matching adjacent areas. Materials_______________ Location: A/C Closet Labor __________________ Size: 32X80 INSTALL ENERGY RECOVERY VENTILATOR: Select Energy Recovery Ventilators (ERV) that are ENERGY STAR®, equivalent, or better. Select efficient equipment. This whole building ventilation must be installed in a dwelling unit to provide indoor air quality that is acceptable to human occupants. Ventilator requirements are 40 to 50 CFM's continuous flow and a rating of 1 zone or less. Contractors must follow program requirement and information provided by the ASHRAE 62.2 VENTILATION CFM rate. Install all electrical wiring according to the manufacturer specifications and applicable code. All installation terminations: per manufacturer's specifications and applicable code, All jobs must meet and be according with SWS work specifications. The ducts must vent directly to the outdoors with bugs screening (Through an insulated duct to gable or wall) never into the attic or into other locations within the home. Materials and methods must comply with Miami-Dade County regulations and Weatherization Program Guidelines. Building Permit must be separate from other ventilation permits. Materials _____________ Location: Hallway Labor ________________ Permit Fees ____________ REPLACE WATER HEATER: Furnish and install water heating unit that: has an Energy Factor (EF) of 0.93 or better fits in the installation space with the required clearances and provides sufficient hot water for the home and occupants. Select efficient and properly sized water heater. If appliance is installed in or above conditioned space or in a location where water damage could occur, install a drain pan according to the requirements of the IRC Drain pan to the exterior of the building to prevent water damage from leaking water. Install water heater in compliance with applicable code e.g., NFPA 70, IRC, IBC, IMC) and manufacturer specifications and safe installation. Ensure that anode rod is accessible for replacement Ensure the appliance can be easily maintained and replaced. Temperature and Pressure (TandP) relief valve per the IRC and manufacturer specifications Select piping material based on IRC requirements. Select durable and correctly sized pipe insulation that: is a minimum of R-3 is a vapor retarder is the correct interior diameter to match pipes is UV-protected if installed outside. Safe, continuous, and durable installation. Electrical connection must be upgraded to manufacturers’ recommendation and Florida Building Code and/or any applicable Miami-Dade County Building Codes. All jobs must meet and be according with SWS work specifications. Permanently remove equipment from job site and recycle or dispose of removed equipment and refrigerant in accordance with local and federal law (e.g., EPA Section 608 of Clean Air Act of 1990) Old equipment is permanently decommission removed from service, protect the environment, and comply with regulations. Materials ___________ Size: 40 Gal Labor ______________ Type: Storage W/H Permit Fees __________ Disposal Fee ________ Subtotal Materials: _____________ Subtotal Labor: ________________ Subtotal Permit Fees:___________ TOTAL PROJECT COST: ________ Scope of Work # 6 Pages 1 - 9 Folio # 30-5910-031-1330 Work Site Address: 11421 SW 144 Avenue INSTALL SMOKE DETECTORS: Furnish and install battery-operated smoke alarms that are listed and labeled in accordance with UL 217 and have sealed, non-replaceable, 10-year batteries along with a tamper proof cover is required. Install battery-operated smoke alarms in the locations required by the Authority Having Jurisdiction (AHJ) Install battery-operated smoke alarms in accordance with the manufacturer's instructions and Miami Dade residential code. Materials_____________ Locations: In All Locations needed Labor________________ Quantity:4 INSTALL CO DETECTOR: Furnish and install CO alarms (Carbon Monoxide Detector) that are listed and labeled in accordance with UL 2034, or approved by the authority having jurisdiction, and have a minimum of: 10-year manufacturer's warranty Contain internal non-replaceable batteries along with tamper proof covering near gas appliances. Install CO alarms in the locations required by the Authority Having Jurisdiction (AHJ) Install CO alarms in accordance with the manufacturer's instructions The installed location must not interfere with or obstruct any cabinet or drawer functions. Materials_______________ Location: Hallway Sleeping Room Area Labor__________________ Quantity: 1 INSTALL SHOWER HEADS: Furnish and install, low-flow Showerhead made of ABS thermoplastic with Chrome-plated finish, self-cleaning and maintenance free, non-removable flow compensator. rated for 2.5 gallons per minute (GPM) or less that includes an antiscald valve. If multiple heads are provided in a shower stall, the total flow rate may not exceed 2.5 GPM. The showerhead will be tested to determine if equipment is tightened adequately to prevent leakage at the point of connection Materials ______________ Location: In All Bathrooms Labor _________________ Quantity: 2 INSTALL AERATORS: Furnish and install Faucet aerators with a flow rate of 2.2 GPM or less, constructed of solid brass with polished chrome finish. Maximum flow rate of 2.2 GPM (gallons per minute) Kitchen must be swiveling type with multi spray. • Faucet aerators will be tested to determine if equipment is tightened adequately to prevent leakage at the point of connection. Materials ______________ Quantity: 3 Labor _________________ Locations: In All Locations PROVIDE A/C AIR FILTER: Remove and replace disposable pleated AC filter with filtration must meet a minimum efficiency of MERV 8 or better and leave the extra with homeowner. Filter opening must allow filter to be fully removed and inserted without bending or damaging the filter Materials______________ Quantity: 2 PROVIDE LED LIGHT BULBS: Furnish new Energy Star certified LED bulbs, and replace incandescent light lighting level quality required for the intended application (e.g., task lighting, hazards lighting, nightlights) is the highest level of efficiency within a technology (e.g., LED bulbs) are ENERGY STAR® qualified, equivalent or better, and UL approved Install lighting in accordance with manufacturer specifications and applicable code (i.e., NFPA 70, NFPA 101, NECA/IESNA 500) If applicable, clean the lens and reflector before installing new bulb Safe and proper installation. Permanently remove old products from job sites and recycle or dispose of in accordance with local and federal law (e.g., EPA Section 608 of Clean Air Act of 1990) Materials _________________ Quantity 12 Labor ____________________ Location: In All Locations INSTALL BATHROOM EXHAUST FAN: Furnish and install a new 100 CFM exhaust fan with 1 sone or less in the ceiling Remove any attic insulation from around the fixture. The bathroom exhaust fans must have a minimum mechanical exhaust capacity of 50 cfm (cubic feet per minute when tested at final inspection) when operated intermittently Efficiency and quiet equipment at time of installation completed. Exhaust air from bathrooms must be exhausted directly to the outdoors with bugs screening and cannot be recirculated within the residence or discharged into an attic, crawl space, or other areas inside the building. Securely mounted fan using mechanical fasteners and per manufacturer's specifications so that fan housing does not shake, rattle, or vibrate when operating and, Ensure fan and service disconnect switch are accessible for maintenance according to NEC, or applicable building code Material and methods must meet the requirements of the applicable fire safety code (e.g., thermal or ignition barriers), and comply with Miami-Dade County mechanical building codes regulations and Weatherization Program Guidelines. Labor & Materials maximum allowable cost $400.00 per Bathroom. Follow SWS work specifications. Materials __________ Location: Bathroom 1 Labor ______________ Quantity: 1 Permit Fees __________ REPLACE BATHROOM EXHAUST FAN: Furnish and install a new 100 CFM exhaust fan with 1 sone or less in the ceiling Remove any attic insulation from around the fixture. The bathroom exhaust fans must have a minimum mechanical exhaust capacity of 50 cfm (cubic feet per minute when tested at final inspection) when operated intermittently Efficiency and quiet equipment at time of installation completed. Exhaust air from bathrooms must be exhausted directly to the outdoors with bugs screening and cannot be recirculated within the residence or discharged into an attic, crawl space, or other areas inside the building. Securely mounted fan using mechanical fasteners and per manufacturer's specifications so that fan housing does not shake, rattle, or vibrate when operating and, Ensure fan and service disconnect switch are accessible for maintenance according to NEC, or applicable building code Material and methods must meet the requirements of the applicable fire safety code (e.g., thermal or ignition barriers), and comply with Miami-Dade County mechanical building codes regulations and Weatherization Program Guidelines. Labor & Materials maximum allowable cost $400.00 per Bathroom. Follow SWS work specifications. Materials __________ Location: Bathroom 2 Labor ______________ Quantity: 1 DRYER VENTILATION: Select dryer transition ducting materials that are UL 2158A approved and less than 8 feet in total length with no joints. Select primary dryer ducting material that is 28-gauge metal with a smooth interior Smooth airflow that does not collect lint be UL approved for dryers be installed according to manufacturer specifications be airtight when dryer is operating Safe and airtight lint collection. Verify electrical receptacle meets the requirements of NFPA 70 (Article 422) Safe electrical connection. Vent all clothes dryers outdoors, install a dryer booster fan that is listed and labeled to UL 705 for dryer ducts exceeding 35' in equivalent length. Install ducts according SWS work specifications detail for "Ventilation Ducts” Dryer ducted too outdoors durably and effectively. If a lint collection device is installed, it must: be UL approved, for dryers to be installed according to manufacturer specifications be airtight when dryer is operating. Safe and airtight lint collection. Vent dryer through a termination manufactured for use with dryers that include a backdraft damper. Follow SWS work specifications. Dryer termination is effective, safe and does not inhibit flow. Seal all duct connections with 181B or 181B-M listed material Airtight ducts Materials ___________ Location: W/H Closet Labor ______________ Estimated Quantity: 3 Linear Ft REPAIR DRYWALL AT BATHROOM CEILING & W/H CLOSET WALL: Repair interior drywall at bathroom ceiling, and W/H closet wall, provides all material and labor necessary to close, patch and match adjacent of the surface area. Repair areas may be, but are not limited to, 1/2", 5/8", GWB, MRGWB, and or Duroc board. Repair the bathroom ceiling, assess the damage, and remove all loose or damaged materials. Then, repair or replace the drywall, sand and smooth the area, prime with a mold moisture-resistant primer. When repairing or replacing ceiling drywall, choose mold moisture-resistant materials. All materials used in weatherization must resist mold and rot if exposed to moisture and humidity. All jobs must meet and be according with SWS work specifications Materials: _____________ Location: Bathroom/ W/H Closet Labor ________________ Estimated Quantity: 3 SQFT REPAIR WINDOW WEATHERTIGHT TO CLOSE PROPERLY: Provide all necessary materials and labor to install replacement any window components, tracks, sashes and tightening adjusting balances any misaligned sashes, tracks, loose hardware, screws on hinges, and handles. Select sealants that are compatible with their intended surfaces, allow for differential expansion and contraction between dissimilar materials, Pest-resistant materials meet the requirements of the applicable fire safety code (e.g. thermal or ignition barriers), and for use inside the pressure boundary select low volatile organic compound (VOC) sealants that meet independent testing and verification. And that meet independent testing and verification protocols. All repair and installation must be according with SWS work specifications (glazing, caulking, sealant, paint, locks, hardware or suitable lubricant to have all designated windows restored and repaired to function as originally intended. Replacing worn weatherstripping and addressing any damaged or broken parts and locking mechanisms etc. Material _____________ Location: In all locations Labor _______________ Quantity: 4 REPAIR SLIDING GLASS DOOR: Furnish and provide all necessary labor and material to repair and restore the door to function as originally intended. Work may include hardware removal and replacement of Tracks, Wheels and Handles. All repair and installation must be according with SWS work specifications (glazing, caulking, sealant, paint, locks, hardware or suitable lubricant to have all designated windows restored and repaired to function as originally intended. Replacing worn weatherstripping and addressing any damaged or broken parts and locking mechanisms etc. Materials ______________ Location: Rear Side- South side Labor _________________ Quantity: 4 SGD REMOVE AND REPLACE EXTERIOR FRENCH DOOR: Furnish and install new out-swing impact resistant 1-3/4" pre-hung insulated steel entry door with all needed hardware, trim, peep hole and locksets to replace existing doors. Unit to include jamb, keyed entry lock, single cylinder, metal threshold, weather strip, door stopper or safety chain, and door is to swing out with security hinges. Select doors that meet the SHGC, U-value, and air leakage requirements of the work order. Select the correct and safe new doors that meet the safety requirements of the location where they are installed. Doors are required to have a fire-resistance rating, all weather strips and sealants applied to the door will be compatible with the listing of the door materials that meet the requirements of the applicable fire safety code (e.g., thermal or ignition barriers), and low volatile organic compound (VOC) materials for use inside the pressure boundary that meet independent testing and verification protocols. Door replacement and installation must be according with SWS work specifications. • Unit approved by MDC Product Control Division to resist hurricane forces, per the FBC and Miami-Dade Building Code. Doors must have NOA approved by Miami-Dade County and/or FBC approval. Provide industry standard trim on outside (Brick mold) and inside (Casing mold) Patch stucco surface around door to match existing finish. Paint the door and trim to match the existing paint color and finish. Materials __________ Location: Front Door Labor ____________ Estimated Size: 60 x 80 Permit Fees _______ INSTALL ENERGY RECOVERY VENTILATOR: Select Energy Recovery Ventilators (ERV) that are ENERGY STAR®, equivalent, or better. Select efficient equipment. This whole building ventilation must be installed in a dwelling unit to provide indoor air quality that is acceptable to human occupants. Ventilator requirements are 40 to 50 CFM's continuous flow and a rating of 1 zone or less. Contractors must follow program guidelines and information provided by the ASHRAE 62.2 VENTILATION CFM rate. Install all electrical wiring according to the manufacturer specifications and applicable code. All installation terminations: per manufacturer's specifications and applicable code, All jobs must meet and be according with SWS work specifications. The ducts must vent directly to the outdoors with bugs screening (Through an insulated duct to gable or wall) never into the attic or into other locations within the home. Materials and methods must comply with Miami-Dade County regulations and Weatherization Program Guidelines. Building Permit must be separate from other ventilation permits. Materials _____________ Location: Hallway Labor ________________ Quantity: 1 Permit Fees ____________ MAKE A NEW ATTIC HATCH THE EXISTING: A. Build or Install a dam around the attic hatch opening to maintain the full level of ceiling insulation to the edge of the opening and to prevent insulation from falling into living space. Frame the opening with dimension lumber, OSB, or plywood. Don’t use cardboard or foam board to dam around access hatches. (Must use plywood or other durable rigid material) Cardboard and foam board aren’t durable materials where they are readily accessible to occupants. Repair or replace the attic door cover if damaged. B. Install foam board in layers to the attic door and secure by gluing the foam to prevent heat transfer through the access door using construction adhesive to achieve R-30 or the greatest attainable R-value that still allows the door to function. Permanently attaches weatherstripping around the entire perimeter of attic-access door on frame to create an effective air seal between the door frame and the door. There shouldn’t be air infiltration in the surrounding of the attic door entrance. Select low volatile organic compound (VOC) sealants that meet independent testing and verification protocols methods. All jobs must meet and be according with SWS work specifications. Materials_____________ Location: Bedroom Closet Labor________________ REPLACE TANKLESS WATER HEATER: Verify current plumbing infrastructure is sufficient to support the installation(s) and is leak-free Verify adequacy of plumbing. Furnish and install a water heater that: is ENERGY STAR® certified, equivalent, or better fits in the installation space with required clearances provides sufficient hot water for the home and occupants Select efficient and properly sized water heater. Install water heater in compliance with applicable code e.g., NFPA 70, IRC, IBC, IMC) and manufacturer specifications and safe installation. Ensure that anode rod is accessible for replacement Ensure the appliance can be easily maintained and replaced. If conflict exists between code and manufacturer specifications, apply the more restrictive requirement. Compliant and safe installation Electrical connection must be upgraded to manufacturers’ recommendation and Florida Building Code and/or any applicable Miami-Dade County Building Codes. All jobs must meet and be according with SWS work specifications. Permanently remove equipment from job site and recycle or dispose of removed equipment in accordance with local and federal law (e.g., EPA Section 608 of Clean Air Act of 1990) Old equipment is permanently decommission removed from service, protect the environment, and comply with regulations. Materials ___________ Type: Tankless W/H Labor ______________ Permit Fees __________ Disposal Fee ________ Subtotal Materials: _____________ Subtotal Labor: ________________ Subtotal Permit Fees:___________ TOTAL PROJECT COST: ________
Technical Certification: General Building Contractor, Building Contractor
Files
Files size/type shown when available.
BidPulsar Analysis
A practical, capture-style breakdown of fit, requirements, risks, and next steps.
FAQ
How do I use the Market Snapshot?
It summarizes awarded-contract behavior for the opportunity’s NAICS and sector, including a recent pricing band (P10–P90), momentum, and composition. Use it as context, not a guarantee.
Is the data live?
The signal updates as new awarded notices enter the system. Always validate the official award and solicitation details on SAM.gov.
What do P10 and P90 mean?
P10 is the 10th percentile award size and P90 is the 90th percentile. Together they describe the typical spread of award values.